Heat Pump Sound Attenuation & Upgrade Options

Following is a list of upgrade options including heat pump sound attenuation and other extras you may or may not have known that we can do for your project.

However, if you do not find an option that you are looking for please let me know, as not all options have been listed.

• 24/7 Water temperature sampling pump operation timer
• Reduce running costs & Saves energy use by checking water temperature at set intervals reducing the need for 24/7 water pump operation.
• Both reducing water pump use and heat pump demand when you need it.

• 304 Stainless steel chassis are standard.
• Significantly increase the lifespan of your heat pump.
• Increased warranty on chassis to 10 years.
• Providing a highly durable and attractive clean finish with low maintenance costs.

• Lowline – Reduced unit Hight for limited space builds like, under the pool or in a car park.
• Slim – Reduced unit width for where serviceable space is limited
• Extra service access points – for ease of maintenance
• Complete custom designs – To meet special project needs
• Fan location options – Standard Front, Top and left and right discharge options.
• Heat Pump Sound Attenuation – Bodywork Kits and Acoustic foam inlays available
• Implant or Outdoor Builds – To suit almost any build location
• Stage Splitting – Limited space, can’t fit several units then use a single larger unit to drive multiple pools.
• Stackable units – Limited space, reinforced units to allow for vertical unit stacking.
• Air to Water or Water to Water – Different methods of heat transfer.
• Energy Recapture & Ventilation Options – Improve efficiency by capturing lost pool heat energy.
• Heater, Chiller or Heater Chiller Reverse Cycle – All our systems can be set up for different water heating or chilling requirements.

• When upgrading a pool heating system, often there are site restrictions, an onsite build helps address these
• 1# We build the unit in-house and complete all in-house testing.
• 2# Disassemble unit into major components, keeping the integrity of the heat pump
• 3# Deliver unit components to the project site. Allows the carrying of components into location
• 4# Rebuild unit in place.
• 5# Re-test unit and commission for use.

• An extremely durable coating that will significantly increase the lifespan of your heat pump.
• Helps to prevent or significantly reduce coil deterioration especially in highly corrosive environments.
• Deep Set coils are used to increase surface area whilst minimising space.

• Pre-programmed sophisticated safety and control logistics.
• An intelligent energy management controller ensures reliable operation throughout the swim season.
• Coupled with this controller is electrical, refrigerant and water flow safety devices ensuring equipment protection and peace of mind.
• External Contact points for BMS System connectivity

• Crankcase Heaters: prevents cold liquid refrigerant migration.
• Compressor thermal over-temperature cut-out.
• Compressor pressure safety switches (LP & HP)
• Anti-Freeze thermostat for protecting heat exchangers
• Low water pressure or paddle flow safety switches C/W fault light indicator
• Suction accumulator to protect the compressor from liquid refrigerant return failure.

• This device alleviates hassles commonly experienced by domestic customers having to pay additional costs associated with installing 3-phase metering systems.
• It enables the selection and use of our larger single-phase heat pumps at a marginal cost to the pool owner.
• No need for expensive inverter technology when you have a soft starter installed.

• Pressure switches are standard for heat pump protection
• Prevents a heat pump running with no water flow.
• Paddle Switches are required when the heat pump is more than 2m higher or lower than the pool level

• Crankcase Heaters: prevents cold liquid refrigerant migration.
• Compressor thermal over-temperature cut-out.
• Compressor pressure safety switches (LP & HP)
• Anti-Freeze thermostat for protecting heat exchangers
• Low water pressure or paddle flow safety switches C/W fault light indicator
• Suction accumulator to protect compressor from liquid refrigerant return failure.

• When under extensive use, request our fan upgrade options.
• Heavy-duty P-Block Fans
• Greaseable P-Bock with sealed bearings for wear protection.
• Increases the life of your fans significantly

• In most heat pumps in the market, you simply plumb the water pipes to the unit and turn on the water.
• However too much or too little water flow will affect your heat pumps performance and heating capacity.
• If too much water goes through a heat pump the water does not stay in the heat exchanger long enough to pick up the heat required to bring the pool to your desired levels.
• This will cause you to unnecessarily run the heat pump for extended periods of time to make up for the inefficiencies caused by the low internal pressures and low water flow.
• A too small amount of water flow will also cause your heat pump to run inefficient and drive up internal pressures, potentially to critically high levels.
• These high levels can cause refrigerant issues such as burnt refrigerant, leaks and other known issues.
• Variable speed water pumps can also have a negative effect on heat pumps by acerbate these issues.

• Winter Versus Summer: Did you know that the amount of water passing through a heat pumps’ heat exchanger will also vary in correlation with the ambient temperature.
• Most heat pumps do not address this issue causing either too much or too little water flow through the heat pump’s heat exchanger.
• Most heat pumps address these seasonal issues by allocating a water flow rate mid-way between the two in an attempt to minimise the water flow impact.
• Or set the unit for maximum flow rate and let you be wary about excess running costs.

• Toyesi’s Unique Water Balance Valves are used to adjust water flow levels through the heat exchanger, allowing for excess water flow to safely bypass the heat pump and delving the correct amount of water through the heat pump for optimum heat pump performance.
• This means you can set your water pump up and not be wary about any variable speeds of flow.
• You can adjust the value as often or as little as you like, but we recommend a minimum of twice a year to allow for maximum efficiencies during the cooler winter or hotter summer month

Have you ever purchased a piece of equipment and wish that you could change its look and feel to fit in better with your environment? Maybe even a change in colour, or maybe a whole look and feel.

• Toyesi stainless steel chassis are known for their professional and desirable finish
• Improve the pool athletics by changing the outward appearance of the heat pump.
• Change the outward appearance of the heat pump using wraps and skins.
• Common Choices:
  • Wood Grain
  • Garden Scene
  • Black and white Cow, Camo and other prints
  • Logos

Follow us on Facebook or LinkedIn